| | Preview | User | Replies | |
 | "LP to nat gas conversion " , posted Wed 5 Nov 17:16
I have an Aire Flo furnace. I need to convert to nat gas from LP. The valve is a honeywell SV9501H2409. The local hvac guys say they cant get a kit to convert it back to nat gas and that I need to buy ... read more |
pauper
 |
Replies (2)
Re(1):LP to nat gas conversion - djgilbert
Re(2):LP to nat gas conversion - agatto2
| |
| "Have O and B wires, but new thermostat... " , posted Wed 5 Nov 15:48
Hi. My current system has the following 8 wires: B,0,L,X,W2,R,Y,G. I purchased a new Honeywell thermostat (RTH7600D1014 - touch screen model) which only has 1 O/B connector. I followed the instruction ... read more |
mdupls
|
Replies (11)
Re(1):Have O and B wires, but new thermostat. - mdupls
Re(1):Have O and B wires, but new thermostat. - Houston204
Re(2):Have O and B wires, but new thermostat. - mdupls
Re(3):Have O and B wires, but new thermostat. - Houston204
Re(3):Have O and B wires, but new thermostat. - mdupls
read more
| |
| "Strange Rheem Criterion II furnace problem " , posted Wed 5 Nov 15:28
Hi all, I have a Rheem furnace criterion II that is behaving a bit strange a month ago. When thermostat calls for heat, it will turn on and run its cycle and produce heat, everything seems working fi ... read more |
jasonw6
|
Replies (4)
Re(1):Strange Rheem Criterion II furnace prob - SAVED
Re(2):Strange Rheem Criterion II furnace prob - jasonw6
Re(3):Strange Rheem Criterion II furnace prob - wingnut_2u
Re(4):Strange Rheem Criterion II furnace prob - jasonw6
| |
| "Trane Problem " , posted Wed 5 Nov 14:58
I have a 6 year old 90% Trane gas furnace that is failing.I searched the internet and all the Trane problems seem to be the same thing -- a vacuum leak that keeps the pressure switch from ... read more |
johnfull
|
Replies (0)
| |
| "Bought a Honeywell RTH7500 Thermo " , posted Wed 5 Nov 13:33
Replacing a Generic Digital Lux with the above programable.On the Lux the following wires were connected:White Wire to WRed Wire to RH Jumper to RCBlue Wire to BBrown Wire to O
read more |
Jormaboy
|
Replies (2)
Re(1):Bought a Honeywell RTH7500 Thermo - dac122
Re(1):Bought a Honeywell RTH7500 Thermo - Houston204
| |
| "No control over back-up " , posted Wed 5 Nov 13:09
Maytag heat pump Model PSH2BC036K. Heat pump and air cond. working fine until outside temp drops below 40 degrees. Electric back-up then comes on but continues to heat way above thermostat setting. We ... read more |
kut
|
Replies (3)
Re(1):No control over back-up - dac122
Re(2):No control over back-up - kut
Re(1):No control over back-up - Schock Therapy
| |
| "No hot air comming from heat pump " , posted Wed 5 Nov 11:05:
I went home this weekend and the tempature dropped to the mid 40's. I turned on the heat and the heat pump only blew out cold air. It was as if I only turned the fan setting was on. I turned the therm ... read more |
agwood75
|
Replies (7)
Re(1):No hot air comming from heat pump - frankout
Re(1):No hot air comming from heat pump - Jojo98
Re(2):No hot air comming from heat pump - agwood75
Re(3):No hot air comming from heat pump - SAVED
Re(4):No hot air comming from heat pump - SAVED
read more
| |
| "Diagnosing defrost issue with YorkGuard 4 " , posted Wed 5 Nov 09:24
I'm trying to determine where the problem exists with a YorkGuard 4 module in a York HP during defrost. I don't have the manual but I recall reading somewhere if you jumper J & C terminals it will kic ... read more |
dac122
|
Replies (0)
| |
| "recommendation for new forced air furnace " , posted Wed 5 Nov 01:43
Hi, I need to replace my old furnace as it has a crack in it (PG&E shut it down and posted a hazard notice). I got quotes from three reputed contractors. They are pushing Amana, Trane, Kenmore (Ca ... read more |
rama
|
Replies (4)
Re(1):recommendation for new forced air furna - learner
Re(2):recommendation for new forced air furna - jmar
Re(3):recommendation for new forced air furna - Schock Therapy
Re(4):recommendation for new forced air furna - agatto2
| |
| "turn off single zone of multi-zone heat sys " , posted Tue 4 Nov 23:23
have 1 zone that is constantly heating. Thermostat is now turned all the way down. Heat continues. In this oil-fired hot water baseboard heat system, is there a way to turn off just one zone on a m ... read more |
psdmgr
|
Replies (4)
Re(1):turn off single zone of multi-zone heat - learner
Re(1):turn off single zone of multi-zone heat - learner
Re(1):turn off single zone of multi-zone heat - hemikota804
Re(2):turn off single zone of multi-zone heat - psdmgr
| |
| "help " , posted Tue 4 Nov 22:09
Hello I have an old boiler in my basement. It works great but its an upfeed gravity boiler with no pump. Has two zones. So two feed lines and two return lines. Just wondering if I could add a pump to ... read more |
prudendl
|
Replies (2)
Re(1):help - hemikota804
Re(2):help - Freon
| |
| "Carrier Heat Pump Condenser Won't Run/Stay on " , posted Tue 4 Nov 18:13
Our house is like 4 years old but I never used the Carrier heat pump in the bonus room. Anyway decided to use it but it isn't working properly. When I cut the heat on, the aux heat turns on initiall ... read more |
dawg1
|
Replies (4)
Re(1):Carrier Heat Pump Condenser Won't Run/S - theduke03
Re(2):Carrier Heat Pump Condenser Won't Run/S - dawg1
Re(3):Carrier Heat Pump Condenser Won't Run/S - theduke03
Re(4):Carrier Heat Pump Condenser Won't Run/S - hemikota804
| |
| "Honeywell RTH7600 " , posted Tue 4 Nov 17:46
Hello,I would like to replace my Lennox thermostat, P/N 36G6901, with a new Honeywell RTH 7600 but the wiring is different. I have a Lennox heat pump with electric emergency heat that is about 18 ... read more |
jawerk
|
Replies (2)
Re(1):Honeywell RTH7600 - Houston204
Re(2):Honeywell RTH7600 - jawerk
| |
| "Trane E90 Check Line Polarity " , posted Tue 4 Nov 15:12
The diagnostic light blinks 2X, "System Lockout, No Flame, Check line Polarity". It does this 1 out of every 3 times. If I turn the furnace off & restart it will normally light. HELP ... read more |
baltohio
|
Replies (2)
Re(1):Trane E90 Check Line Polarity - Freon
Re(2):Trane E90 Check Line Polarity - hemikota804
| |
| "dog used bathroom on AC " , posted Tue 4 Nov 15:06
I just received one estimated on my air conditioner. But the coil like material has eroded due to dog urinating on it. I was told the whole air conditioner needs to be replaced. But the compressor wor ... read more |
Mysteee
|
Replies (2)
Re(1):dog used bathroom on AC - aircooled
Re(1):dog used bathroom on AC - Freon
| |
| "furnace will not light " , posted Tue 4 Nov 14:14
Having a problem with a Haier HGA080N3H, inducer motor turns on but will not light. Inducer fan stays on even thuogh the furnace does not light. Any comments would be greatly appreciated. ... read more |
rmart68
|
Replies (1)
Re(1):furnace will not light - Freon
| |
| "noise when oil burner shuts off " , posted Tue 4 Nov 10:05
hello when my oil burner shuts off i hear a sound like a steam sound. have no water leaks i shut off the main feed to see if there is a drop in pressure .pressure stays where it should .burner is runi ... read more |
evan
|
Replies (2)
Re(1):noise when oil burner shuts off - Freon
Re(2):noise when oil burner shuts off - jmar
| |
 | "Heat pump issues " , posted Mon 3 Nov 18:07:
I have a Goodman ARUF036-00A-1 Heat pump and a Honeywell RTH3100 t-stat.I installed the t-stat at the beginning of the summer and everything was ok using the AC. Now that the weather is getting c ... read more |
dannys12
|
Replies (2)
Re(1):Heat pump issues - holderlehvac
Re(2):Heat pump issues - Houston204
| |
| "24V wiring " , posted Mon 3 Nov 16:33
Would appreciate your advice on the 24V wiring for a gas furnace and 410A heat pump (Armstrong Air Products). A new installation with A-coil in furnace. Furnace has panel strip for R, C, W, G, Y. He ... read more |
amp
|
Replies (1)
Re(1):24V wiring - Houston204
| |
| "York Diamond 90 runs continuosly " , posted Mon 3 Nov 16:11
York Diamond 90 intermittently blows continuously. It started happening this summer even when the thermostat was turned down to 50 and it was not calling for heat. There is no A/C on this system. I ha ... read more |
tonymaud
|
Replies (3)
Re(1):York Diamond 90 runs continuosly - Freon
Re(2):York Diamond 90 runs continuosly - tonymaud
Re(3):York Diamond 90 runs continuosly - yuri
| |
| "I need help with the white-rogers 1f86-4441 " , posted Mon 3 Nov 15:29
I have a white-rogers 1f86-444 and i can not find the manul. I need to know how to hook up the wires. does anyone have a pic of the manual or know where i can find one at. ... read more |
crazzycaines
|
Replies (1)
Re(1):I need help with the white-rogers 1f86- - Freon
| |
| "THANKS !! " , posted Mon 3 Nov 08:23
Thanks a lot for your reply. I appreciate your time. ... read more |
Tidwell
|
Replies (0)
| |
| "outside fan " , posted Mon 3 Nov 08:08
outside fan gets warm but will not run -spins if blade started by hand - is it motor or starter capacitor? ... read more |
hwbuck
|
Replies (2)
Re(1):outside fan - Silvertop
Re(2):outside fan - Freon
| |
| "burners don't stay lit - sometimes " , posted Sun 2 Nov 21:17
My 16 year old furnace recently had a pre-season maintenance. [forced-air, hot surface ignitor and flame sensor]After that, it ran fine for a day, then started short-cycling. The burners would ign ... read more |
rayne
|
Replies (2)
Re(1):burners don't stay lit - sometimes - jmar
Re(2):burners don't stay lit - sometimes - hemikota804
| |
| "AC and furnace on? " , posted Sun 2 Nov 19:47
When my furnace kicks, the AC does too? Any idea why and what I can do to fix it? ... read more |
switch
|
Replies (1)
Re(1):AC and furnace on? - Houston204
| |
| "Carrier Infinity " , posted Sun 2 Nov 18:05
I would like to wire my Aprilaire 600 directly to my Carrier MPV Infinity furnace. Should I directly wire the the solenoid directly to the furnace circuit board? If so, should the wires got to the t ... read more |
chiefella
|
Replies (5)
Re(1):Carrier Infinity - jmar
Re(2):Carrier Infinity - chiefella
Re(3):Carrier Infinity - jmar
Re(4):Carrier Infinity - chiefella
Re(4):Carrier Infinity - chiefella
| |
 | "help " , posted Sun 2 Nov 15:54
problem what is my system type What is it. I have a trane xe1000 heat pump modal # twr030c100A2 outside and a trane 2 1/2 -5 ton- convertible air handler modal # TWE030C140 when asked on my new stat i ... read more |
crewchief25
|
Replies (2)
Re(1):help - jmar
Re(2):help - crewchief25
| |
| "help " , posted Sun 2 Nov 14:40
I am attempting to change my old Trane weathertron thermostat BAYSTAT240 with a new honeywell RTH7000 and i ran into a problem there is am extra wire that was attached to the T terminal but there is n ... read more |
crewchief25
|
Replies (3)
Re(1):help - jmar
Re(2):help - crewchief25
Re(3):help - Houston204
| |
| "Aprilaire Carrier MPV Infinity " , posted Sun 2 Nov 14:04
I recently purchased an Carrier infinity thermostat for my heating and airconditioning system and have a few questionms regarding the wiring of some accesssories. I would like to wire my Apri ... read more |
chiefella
|
Replies (9)
Re(1):Aprilaire Carrier MPV Infinity - techshawn
Re(2):Aprilaire Carrier MPV Infinity - Houston204
Re(2):Aprilaire Carrier MPV Infinity - chiefella
Re(3):Aprilaire Carrier MPV Infinity - chiefella
Re(4):Aprilaire Carrier MPV Infinity - Houston204
read more
| |
| "wont ignite " , posted Sun 2 Nov 10:52
I hav a Trane XE80 1994....I know...I'm due. My problem is when there isa call for heat, "the glow plug" doesn't glow to ignite the gas. It did this yesterday and I remoed the plug to look at it and i ... read more |
Tidwell
|
Replies (1)
Re(1):wont ignite - jmar
| |
| "he360 humidifier " , posted Sun 2 Nov 08:35
I just installed a he 360 humidifier with a h8908b humidistat. Everything appears to be working,solenoid kicks in and water is coming out of the drain tube when the furnace blower kicks in. My first q ... read more |
terrybib
|
Replies (1)
Re(1):he360 humidifier - Freon
| |
| "Pressure reading at inducer motor. " , posted Sun 2 Nov 07:35
I am working on a 5 yerar old Trane 92%,80k BTU The pressure switch is not closing all of the time. We have checked the flue for obstructions,water traps. etc. Placed my manometer on it and it reads ... read more |
caseiter
|
Replies (3)
Re(1):Pressure reading at inducer motor. - johnfull
Re(2):Pressure reading at inducer motor. - oldmangobles
Re(3):Pressure reading at inducer motor. - hemikota804
| |
| "Pressure Switch " , posted Sun 2 Nov 06:27
I have a goodman Evcon furnace, im always getting the 3 blinking flash green light saying the pressure switch is open, im just wondering where this switch is? Please help ... read more |
djhotgq
|
Replies (1)
Re(1):Pressure Switch - oldmangobles
| |
| "Heat Pump problems " , posted Sat 1 Nov 22:01:
I have spent the day troubleshooting my 1.5 year old American Standard heat pump. It is a 2 ton 13 seer package unit. The problem is, during heat call the suction pressure drops out the bottom and the ... read more |
ETaylor
|
Replies (8)
Re(1):Heat Pump problems - t-stat
Re(2):Heat Pump problems - ETaylor
Re(3):Heat Pump problems - t-stat
Re(4):Heat Pump problems - ETaylor
Re(4):Heat Pump problems - ETaylor
read more
| |
 | "Wiring from York to Hunter " , posted Sat 1 Nov 21:23
I am trying to replace my York T874R1046 thermostat with a programmable Hunter 44360. This is a York heat pump system (N2AHD10A06A).Currently my York is wired as such:W = whiteB = ... read more |
dbarelic
|
Replies (2)
Re(1):Wiring from York to Hunter - Houston204
Re(2):Wiring from York to Hunter - Houston204
| |
| "Trane XE1200 not working " , posted Sat 1 Nov 21:08
My trane has decided not to work. With the screwy weather we have been having, my wife decided to switch from heat to air and nothing happened. Is there a reset switch or something I could flip. Or ... read more |
madcrow
|
Replies (1)
Re(1):Trane XE1200 not working - madcrow
| |
| "Aux Heat Wired wrong Carrier Heat Pump " , posted Sat 1 Nov 19:35
I have a Carrier Heat Pump Model 38YCM024310, a Intertherm electric Furnace (FEBA-012HAO-01), and a Lux programmable tstat (HPT2110 or PT2110 or simply the PT2100 series). Everything runs fine even Au ... read more |
SilveradoZ71
|
Replies (2)
Re(1):Aux Heat Wired wrong Carrier Heat Pump - Houston204
Re(2):Aux Heat Wired wrong Carrier Heat Pump - SilveradoZ71
| |
 | "Black soot or particles in furnace " , posted Sat 1 Nov 15:26
Thanks for a quick reply. This will help. That is what i thought but couldn't get anyone to agree. ... read more |
Deva
|
Replies (0)
| |
| "Black soot or particles in furnace " , posted Sat 1 Nov 11:38
Furnace which burns Propane in Mountain house has black soot-like particles. Discovered when noticed very tiny black particles arount vents, that when touched became soot like powder. When opened furn ... read more |
Deva
|
Replies (2)
Re(1):Black soot or particles in furnace - Jojo98
Re(2):Black soot or particles in furnace - Freon
| |
| "T8611G Thermostat " , posted Sat 1 Nov 10:59
I have a T8611G and a Carrier Heat Pump. Whenever the unit calls for heat the outside unit never come on. I know the outside unit works because if I call for air the outside unit works fine. I susp ... read more |
bhill66
|
Replies (2)
Re(1):T8611G Thermostat - Houston204
Re(2):T8611G Thermostat - bhill66
| |
